Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in Garland, TX
Gate installation in Garland usually means replacing a rusted steel driveway gate or a rotted cedar gate set on posts that North Texas clay has pushed out of plumb. Most Garland homes were built between the 1950s and 1990s, and the original gate hardware on those properties is reaching the end of its service life. At Bastion Gate Repair, we install automatic and manual gates across Garland ZIPs 75043, 75044, 75045, and 75046, sizing every frame and operator to the elevation changes and fence styles common here. Call (866) 321-6117 for a free estimate on a new gate, operator, or full access system.
Why Garland Homes Are Different
Garland’s housing stock spans two very different eras, and each one shapes gate work differently. In older ZIPs like 75043 near downtown and along Garland Road, homes from the 1950s and 60s often still have their original gate posts: cedar or steel set directly into expansive clay. North Texas soil swells after rain and shrinks in drought, which racks posts off-vertical and leaves gates dragging against the ground or refusing to latch. We regularly lift gates off rusted hinges in those neighborhoods and find the post itself is the real failure point.
In the newer 75044 subdivisions and far north Garland, driveway gates are more likely to be aluminum or steel tube frames hung on powder-coated posts, but the same clay movement works on them. We see operator arms knocked out of travel, pickets that have pulled loose from the frame, and slide tracks buried in soil that has heaved upward. The result is that a Garland gate job often starts as one visible symptom and ends with us correcting two or three underlying problems before the gate is reliable again.
Styles & brands we work with
Our Main Garland Services
Most Garland calls fall into one of two categories: a gate that won’t open or close properly, or an electric operator that has stopped responding. Both are covered below.
Gate Repair in Garland
Mechanical gate repair in Garland usually involves posts that have shifted, hinges that have seized, or wood pickets that have rotted at the groundline from years of clay-soil moisture. We straighten or reset posts, replace hinges and latch hardware, weld cracked steel frames, and rebuild gates that are structurally sound but cosmetically failing. The goal is always the same: a gate that swings or slides cleanly without dragging. For full detail on what we fix and how we price it, see our Gate Repair in Garland page.
Electric Gate Repair in Garland
When an automatic gate in Garland stops mid-travel, won’t respond to a remote, or beeps without moving, the problem is usually in the operator, the safety sensors, or the control board rather than the gate itself. We diagnose the entire system methodically, including loop detectors, photo eyes, and access keypads, and we replace only what has actually failed. For automated gates across Garland’s gated communities and single-family driveways, see Electric Gate Repair in Garland.
What happens when you call
- 1
A real person answersNo phone trees — you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Gate Installation in Garland
Gate installation in Garland is rarely a simple swap. The clay soil under Garland shifts enough that every new gate needs posts set deeper and plumbed more carefully than the one that came out, and the 1950s ranches in older ZIPs sit on lots where the original fence line was never built for an automatic opener. Whether we’re hanging a new steel driveway gate in a 75044 subdivision or replacing rotted wood gates near downtown, we size the frame, the post depth, and the operator to the specific site. For a deeper look at how we approach installation as a full system, see Gate Installation.
Automatic Gate Installation
Signs you need it
You’re opening and closing your gate manually several times a day, or you want controlled entry but are still using a padlock and chain.
What it costs in Garland
Automatic gate installation in Garland typically runs $1,800 to $4,200 depending on gate size, operator type, and the condition of the existing posts.
How we do it
We set or repair the gate posts, mount the operator arm and control box on a poured pad or existing column, run power and low-voltage wiring, then program remotes and safety settings.
Driveway Gate Installation
Signs you need it
Your driveway opening no longer matches the gate, the gate sags enough to drag on the concrete, or you want a gate style that matches a newer fence.
What it costs in Garland
A new driveway gate in Garland, including posts and hardware, usually ranges from $1,300 to $3,800 before automation is added.
How we do it
We measure the opening and grade, set steel posts in concrete below the clay line, hang the gate with adjustable hinges, and align the latch and drop rod so it closes square.
Sliding Gate Installation
Signs you need it
Your property has a wide or angled driveway where a swing gate would block the approach or hit a slope.
What it costs in Garland
Sliding gate installation in Garland falls between $2,500 and $5,500 depending on track length, gate weight, and whether a motor is included.
How we do it
We lay a steel track or cantilever rail system on a level concrete base, install the gate frame with rollers and guides, and mount the operator with safety edges and obstruction sensors.
What Gate Installation Costs in Garland
| Item | Typical range in Garland |
|---|---|
| Manual gate and post replacement | $1,300 – $3,800 |
| Automatic gate with single operator | $1,800 – $4,200 |
| Sliding gate with track and motor | $2,500 – $5,500 |
Do I need a permit to install a gate in Garland?
Most single-family gate replacements don’t require a permit in Garland, but driveway gates near a corner or public sidewalk may need to meet setback and visibility rules. We check those requirements before starting.
Can you match my existing fence and gate style?
Yes. We match steel, aluminum, and wood gate frames to existing 6-foot cedar privacy fences and common driveway gate patterns in Garland, so a new gate doesn’t look like an afterthought. Call (866) 321-6117 for a design and quote.
Brands We Service in Garland
We stock parts and service operators from Viking, Ghost Controls, DoorKing, and Elite, along with five other major gate brands. That covers residential slide and swing openers as well as commercial operators on Garland apartment and business entrances. Most common control boards, remotes, and safety edges are available locally or within a day. See our brands for the full list.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in Garland, TX
| Service | Typical range in Garland |
|---|---|
| Hinge replacement | $180 – $400 |
| Gate post reset | $350 – $700 |
| Gate frame welding | $150 – $500 |
| Wood gate rebuild | $400 – $1,000 |
| Automatic gate installation | $1,800 – $4,200 |
| Driveway gate installation | $1,300 – $3,800 |
| Sliding gate installation | $2,500 – $5,500 |
| Full operator replacement | $1,500 – $3,000 |
| Control board replacement | $450 – $1,100 |
| Safety sensor replacement | $250 – $600 |
Prices in Garland push higher when a clay-heaved post has to be dug out and re-poured, when an operator needs new conduit or a longer power run, or when a gate is so rusted that welding new steel makes more sense than patching. Every job is quoted before work starts, and that’s the number on the invoice.
Neighborhoods We Serve in Garland
We cover all Garland ZIP codes: 75043, 75044, 75045, and 75046. That includes older neighborhoods near downtown and Garland Road where original cedar posts are failing, as well as the north Garland subdivisions where automatic driveway gates are standard. Typical response for a repair call in Garland is same-day or next-day depending on parts.
- Downtown Garland
- North Garland (75044)
- South Garland (75043)
- Firewheel
- Coomer Creek
Service Area – Cities Near Garland
Bastion Gate Repair works across northeast Dallas County and the surrounding suburbs. In addition to Garland, we serve Richardson, TX, Sunnyvale, TX, University Park, TX, and Mesquite, TX.
Serving Garland, TX — Our Local Coverage Area
We’re based in the Garland area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Garland
Most Garland repair calls can be scheduled same-day or next-day. If your gate is stuck open and the property is unsecured, we treat it as a priority call. Parts for common brands are usually available within a day.
Many Garland HOAs, especially in newer north Garland subdivisions, require approval before you change gate style, height, or automation. We work with the specs your HOA provides and can help with the measurements and material details they ask for.
Yes. Clay soil movement means many Garland gates need their posts pulled, holes re-dug, and new concrete poured before the gate goes back on. We handle that as part of the same job rather than sending you to another contractor.
Call (866) 321-6117 for a free estimate on gate installation, repair, or automation in Garland. We quote the full price before any work begins, and we stand behind the gate after it’s hung.
What happens when you call
- 1A real person answersNo phone trees — talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you — the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Garland Customers Say
"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."
— Jerome Ingram"Gate works properly now and the price was fair. The one thing is that it took two visits, because the operator model we have is old and the part had to be ordered. They didn't charge for the second trip."
— Greg Parker"Control board fried after a lightning storm. He showed me the burn mark on it, quoted the board, and installed a surge protector on the line so it hopefully doesn't happen again."
— Luis Rodriguez