Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateTrusted Gate Repair for DeSoto Homeowners
A gate that won’t open traps you in your own driveway. One that won’t close leaves your property exposed. In DeSoto, where summer heat warps metal and clay soil shifts under gate posts, both failures are common. Bastion Gate Repair fixes them. We’re the brand-spanning gate specialist run by Brent Calloway, and we service virtually every major gate system on the market, from entry-level residential openers to high-spec commercial operators. One call to (866) 321-6117 gets a technician who has seen your gate’s failure mode before and knows exactly how to correct it. We diagnose the system, not just the symptom.
Key Takeaways
- We repair all gate types: driveway, sliding, iron, wrought iron, metal, wood, and commercial systems.
- Brand-agnostic diagnostics: LiftMaster, FAAC, BFT, Mighty Mule, Linear, Viking, Ghost Controls, DoorKing, and Elite.
- Free estimates: price quoted and agreed before any work starts. No surprises.
- Electric and automated gate expertise is core to our service, not an add-on.
- Single-source provider: repair, electric gate repair, and gate installation under one roof.
Styles & brands we work with
Driveway Gate Repair
Driveway gate repair is the service we’re called for most often in DeSoto, and it typically means one of three things: the gate won’t open, it won’t close, or it opens and closes erratically. Automatic driveway gates fail because they’re mechanical systems exposed to weather, dirt, and daily use. Motors burn out. Sensors misalign. Hinges seize. Track sections shift on clay soil. We diagnose the actual fault, not the most expensive one. Basic hinge and chain adjustments run $150-$300. Board or sensor replacements land between $350-$850. Motor rebuilds average $500-$1,200 depending on the operator. Every price is quoted and agreed before work begins.
Openers and Operators
Mighty Mule openers are common in DeSoto subdivisions and we service them constantly. When an opener fails, we test the control board, capacitor, and limit switches before recommending replacement. That diagnostic discipline keeps a $150 board swap from becoming an $800 motor replacement.
Sensor and Safety Systems
Photo eyes and loop detectors go out of alignment more often than the gate itself breaks. Misaligned sensors make a gate reverse or refuse to close, which reads like a motor failure. We recalibrate and test the full safety circuit before touching anything else, because a gate that ignores its safety edges is a genuine hazard to people and vehicles.
Gate Welding
Gate welding addresses structural failures that hardware alone can’t fix: broken hinges, cracked frames, snapped pickets, or a gate that’s sagging because a weld failed at the corner joint. In DeSoto’s clay soil, gate posts settle and the frame gets stressed at weld points. We perform on-site MIG welding for wrought iron, steel, and aluminum gates, plus reinforcement of weak joints before they fail completely. Small crack repairs run $150-$350. Full hinge replacement with welding averages $300-$700. Reinforcing a sagging frame runs $400-$1,200 depending on gate size and condition.
Hinge and Frame Reinforcement
Most welded gate failures begin at the hinge. When a weld cracks there, the gate drops and drags against the ground or the track. We cut out the failed weld, re-square the frame, and run a full-penetration weld with reinforcement gussets so the repair outlasts the original joint.
On-Site vs. Shop Welding
Small cracks and hinge replacements we do on-site, which gets a DeSoto driveway gate working again the same day. Larger frame reconstructions may need shop welding, but that’s rare. We tell you upfront which applies to your gate, and you approve the price before any spark is struck.
Commercial Gate Repair
Commercial gate repair covers sliding gates, cantilever gates, barrier arms, and automated entry systems on apartment complexes, commercial properties, and gated communities in and around DeSoto. We also handle Lancaster Gate Repair for businesses just south of our core service area. These gates operate at higher cycle counts than residential systems, so failures are usually mechanical: failed rollers, worn drive chains, burned contactors, or operators running past their service life. We handle everything from a single broken trolley arm to full operator replacement. Minor roller and chain service runs $250-$500. Commercial operator replacement ranges from $1,800-$6,500 depending on the system. Linear and DoorKing operators are common in DeSoto commercial settings, and we keep their replacement components in ready stock.
Access Control Integration
A commercial gate isn’t just steel and an operator. It’s tied into keypads, card readers, telephone entry systems, and sometimes vehicle loop detectors at two different approach points. We diagnose the full system so we don’t replace a motor when the actual fault is a failed loop detector under the asphalt.
Priority Commercial Response
When a gated community entrance fails, every resident is affected. We prioritize commercial and HOA gate failures in DeSoto because we understand that a down gate at a community entrance is a security incident as much as a mechanical one. Brent Calloway personally reviews these dispatch orders to make sure nothing sits.
Iron Gate Repair
Iron gate repair means addressing rust, broken welds, bent bars, and failing hinges on ornamental iron gates throughout DeSoto. North Texas humidity and clay soil combine to create exactly the conditions that rust iron gates from the bottom up. We remove surface rust, treat the affected area, weld any failed joints, and repaint or prime as needed. Minor rust treatment and hinge repair runs $150-$400. Replacing bent or broken iron bars runs $250-$600 per section. A full iron gate restoration with rust removal, welding, and a protective coat averages $600-$1,500 depending on gate size.
Rust and Corrosion Control
Rust isn’t cosmetic on an iron gate. It weakens the metal from inside the joint, where you can’t see it until a weld fails and the gate drops. We wire-brush the affected area, apply a rust converter, and then weld or seal with a coating that holds up to DeSoto’s wet springs and hot summers.
Matching Existing Ornamental Work
Iron gates often have decorative scrollwork or custom picket patterns. We fabricate replacements that match what’s already there, so a repair doesn’t look like a repair. That matters for curb appeal and for HOA communities in DeSoto that enforce architectural standards.
Sliding Gate Repair
Sliding gate repair covers gates that roll on track wheels or hang from a cantilever system instead of swinging. Sliding gates fail differently than swing gates. The track gets debris in it. The rollers wear flat. The chain stretches. The motor’s gear rack loses teeth. In DeSoto’s wind storms, cantilever gates get pushed off-center and wedge. We realign, replace rollers and chain sections, and service the operator assembly. Simple roller and track cleaning runs $150-$300. Replacing a worn chain and gear rack averages $350-$800. A full sliding gate motor replacement runs $800-$2,400.
Cantilever vs. Track Systems
Cantilever sliding gates ride on rollers without a ground track, which makes them ideal for gravel driveways but sensitive to misalignment. Track systems work well until clay soil shifts the track or debris jams it. We service both types, and the diagnostic path is different for each. Knowing which system you have before dispatching saves a trip and saves you money.
Motor and Gear Rack Repair
The electric operator on a sliding gate drives a gear along a toothed rack mounted on the gate itself. When teeth wear down, the gate jerks, stalls, or makes a grinding sound. We replace rack sections and remount the operator so the gear meshes correctly, which prevents the failure from recurring in six months.
Wrought Iron Gate Repair
Wrought iron gate repair focuses on hand-forged and ornamental gates that are common on older DeSoto homes and custom properties. True wrought iron is different from modern steel, and it fails differently: the metal itself fatigues and cracks rather than bending. We perform careful weld repairs using material that matches the existing iron, then treat and coat the repair so it weathers consistently with the rest of the gate. Small crack repairs run $200-$400. Resetting and welding a wrought iron gate frame averages $400-$900. Full restoration with multiple weld repairs and refinishing runs $800-$2,000.
Crack Repair and Reinforcement
Because wrought iron is brittle at weld points, a failed weld can’t simply be ground and rewound the same way. We clean the area fully, preheat when needed, and use a compatible filler rod to create a joint that’s stronger than the surrounding metal. Then we reinforce the back side with a gusset where the design allows.
Preserving Original Ironwork
We don’t replace a wrought iron gate when it can be repaired. Original ironwork carries value, and in historic DeSoto properties that matters. We’ll tell you honestly when a repair is feasible and when replacement makes more financial sense, and the price is on the table before you decide.
Metal Gate Repair
Metal gate repair is the broad category covering steel, aluminum, and fabricated metal gates, including the ones installed in newer DeSoto subdivisions. Metal gates fail from impact damage, metal fatigue, and weather exposure. We handle bent frames, broken welds, rusted bottom rails, damaged pickets, and operator mounting failures. Straightening a bent frame and re-welding runs $200-$500. Replacing a damaged section runs $300-$800. Full structural rebuild of a metal gate averages $600-$1,500.
Steel vs. Aluminum Repairs
Steel and aluminum need different welding techniques and different fill materials. Aluminum transfers heat quickly and warps if the welder doesn’t know how to control heat input. We have welders who work both metals daily, which matters when your aluminum driveway gate gets creased by a car bumper and needs to come back square.
Impact and Collision Repairs
A vehicle strike is the most common cause of sudden metal gate failure in DeSoto driveways. The gate gets pushed out of alignment, hinges twist, and sometimes the post itself gets knocked off true. We assess the full structure, not just the visible damage, because a misaligned post will destroy whatever new parts we install.
Wood Gate Repair
Wood gate repair addresses sagging, rot, split boards, failed hardware, and gates that won’t latch properly. Wood gates on DeSoto properties absorb moisture in the spring, dry out in the summer, and eventually split or rot at the joints. We replace rotted members with pressure-treated lumber, reinforce corners with steel brackets, and reset hinges or add a diagonal brace when a gate has dropped. Minor hinge and latch service runs $120-$250. Replacing rotted boards and reinforcing a sagging frame averages $300-$700. A full wood gate rebuild runs $700-$1,800 depending on size and design.
Rot Repair and Reinforcement
The bottom rail is where wood gates fail first. Water sits there. We replace the rotted section, then install galvanized steel brackets where the rail meets the hinge stile. That single reinforcement point is where most wood gates in DeSoto give out, and it’s cheap insurance against a full rebuild later.
Hardware Upgrades
Many wood gate problems are actually hardware problems. Screws strip out. Hinges bend. Latches misalign. We upgrade to heavy-duty hinges with through-bolts and nylon washers, and we set the latch so it engages cleanly every time. A wood gate that closes tight and latches is a gate that does its job.
See the difference
Before
After
Before
After
Before
AfterBrands We Service
We service Mighty Mule openers more than any other residential brand in DeSoto, and we know their failure points: control board shorts in humid springs, failing AC-to-DC chargers, and limit switch drift after power surges. If you’re comparing brands, our post on Choosing the Right Gate Repair Brand: A Buyer’s Guide for DeSoto walks through what matters. We stock Mighty Mule boards and sensors on the truck, which means most Mighty Mule repairs are completed in one visit.
On the commercial side, Linear and FACC operators account for most of what we service in apartment complexes and gated communities. These are high-cycle systems that need more than a part swap: they need proper clutch adjustment, correct motor amp draws, and a clean limit switch calibration. LiftMaster is the other name we see daily on residential estates in DeSoto, and we service the full line from contractor-series openers to smart-enabled systems. Whether your gate says LiftMaster, Mighty Mule, FACC, BFT, DoorKing, or any other make, we can help. If you’re not sure what brand you have, call (866) 321-6117 and we’ll identify it over the phone.
Signs You Need a Pro Right Now
- Your gate only opens halfway, then stops: That’s a symptom of a failing limit switch, a low battery in the backup system, or a motor struggling against excessive resistance. Ignoring it turns a $200 switch replacement into a burnt motor.
- You hear grinding or squealing when the gate moves: Grinding means metal-on-metal contact where there shouldn’t be any. A bad roller or a broken gear in the operator grinds the system down with every cycle, so the repair bill grows each time the gate opens.
- The gate reverses or refuses to close: This is usually a misaligned photo eye or a failed loop detector. But it can also mean the safety edges are malfunctioning, which leaves a heavy gate uncontrolled around children and pets.
- You can see visible weld cracks or a sagging corner: A cracked weld is structural failure already in progress. Once the gate drops and drags, the frame bends, which takes a $300 weld repair and turns it into a $1,200 rebuild.
- The gate opener runs but the gate doesn’t move: This is a drive chain or belt failure, or a stripped gear rack on a sliding gate. Running the motor without movement burns it out quickly, so cut power to the opener and call us.
Our Process, Step by Step
- 1
Inspection and diagnosis: We inspect the gate, hinges, rollers, track, operator, and the full electrical path including sensors and control boards. We use amp meters to test motor draw and multimeters to check board voltage. You get a written diagnosis, not a guess.
- 2
Repair plan and written quote: We explain what failed, why it failed, and what we recommend to fix it. The price is quoted, and you approve it before any work begins. If we find additional damage mid-repair, work stops and we call you with options.
- 3
Repair execution: We perform the repair using OEM or equivalent parts matched to your gate system. Welds are done by welders, wiring by electricians, and operator work by people who know the specific brand on your gate.
- 4
Testing and safety verification: We cycle the gate multiple times, test photo eyes and safety edges, verify the reverse function, and check limits. A gate that leaves our service doesn’t just open and close; it does so safely and consistently.
- 5
Final walkthrough: We show you what we did, explain any maintenance that’ll extend the life of the system, and give you a clean invoice that matches the quote. Then we clean the work area and leave the gate in better shape than before we arrived.
How Much Does Gate Repair Cost in DeSoto?
Gate repair in DeSoto typically runs $150 to $850 for residential fixes and $250 to $6,500 for commercial work, depending on what failed. A basic hinge adjustment or sensor realignment costs $150-$300. Replacing a control board runs $350-$850. An electric motor or operator replacement averages $500-$1,200 for residential gates and $1,800-$6,500 for commercial systems. Weld repairs land between $150 and $1,500 depending on how much structural work is needed. For a deeper breakdown of what to expect, see The Complete Gate Repair Guide for DeSoto Homeowners.
What pushes a gate repair bill higher? Damage that’s been allowed to run is the big one. A gate that’s been grinding for six months has destroyed rollers, chain, and possibly the motor. Access also matters: gates that need heavy equipment or two technicians cost more than a simple hinge service. What helps is prompt diagnosis. The fastest way to keep a repair affordable is to call before the gate stops working entirely, because a gate that partially works is a gate that’s actively damaging itself. Our estimates are free, and every job is priced before the work starts.
Our Service Area Near DeSoto
Bastion Gate Repair serves DeSoto and the surrounding communities across southern Dallas County. We work in Glenn Heights, Oak Leaf, and Ovilla regularly, and we service Duncanville, Cedar Hill, Red Oak, Lancaster, Hutchins, Wilmer, Cockrell Hill, and Ferris. If you’re in any of these communities and your gate won’t close or your opener stopped responding, call us. We schedule repairs throughout the area every weekday, and we route our techs by proximity, so response times across the region stay tight. If you’re in Glenn Heights, see our Gate Repair in Glenn Heights page. In Ovilla, check Gate Repair in Ovilla. For everything else, our Gate Repair in DeSoto page has the full rundown, or go back to our home page to see all services.
Serving DeSoto, TX — Our Local Coverage Area
We’re based in the DeSoto area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
Frequently Asked Questions About Gate Repair in DeSoto
Gate repair is the service of restoring a malfunctioning gate to proper working condition, covering everything from mechanical parts like hinges, rollers, and chains to electrical components like control boards, sensors, and motors. At Bastion Gate Repair, we diagnose the entire system when a gate fails, then repair the specific fault rather than replacing parts that still have service life. Call (866) 321-6117 for a free estimate.
Most residential gate repairs in DeSoto are completed in one visit, typically 1 to 3 hours depending on the fault. A hinge replacement or sensor realignment is under an hour. A full motor or operator replacement may take 2 to 3 hours. Structural welding repairs on large frames can take half a day, and we’ll tell you the expected time before work starts.
Residential gate repair in DeSoto generally runs between $150 and $1,200 depending on what failed, while commercial repairs start around $250 and can reach $6,500 for full operator replacement on high-spec systems. The exact cost depends on parts, brand, access, and how long the problem has been running. Your price is quoted and approved before any work begins.
Yes. We service both brands frequently across DeSoto, and we stock common Mighty Mule boards, sensors, and LiftMaster operator components on our trucks. We also service FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, and Elite. If your operator is a brand we didn’t list, call us anyway; we’ve likely worked on it.
We prioritize emergency calls for gates that won’t close, because an open gate is a security gap. Same-day service is available for most residential emergencies in DeSoto depending on technician schedule, and we keep parts for the most common failure modes in stock. Call (866) 321-6117 and tell us what’s happening.
Yes. Workmanship on our repairs is covered, and the parts we install carry their manufacturer warranties. If something fails because of our repair, we come back and make it right at no charge. We’d rather fix a gate once and have you call us for the next one than patch something that fails again.
Clear the area around the gate so our technician can reach both sides without obstruction, and if you have an opener, make sure the gate is unplugged or the operator is switched off if it’s unsafe to operate. If you have keys or remotes for the system, keep them handy. There’s nothing else to prepare; we bring the diagnostic equipment and most of the parts we’ll need.
Schedule Your Gate Repair Service in DeSoto Today
A gate that doesn’t close is a security gap. A gate that won’t open is a problem every time you leave the house. Call Bastion Gate Repair at (866) 321-6117 and describe what’s happening. We’ll diagnose it over the phone when possible, and schedule a technician for a free, no-obligation estimate. The price is always quoted and approved before work starts.
Written by Brent Calloway, Owner at Bastion Gate Repair, serving DeSoto and surrounding communities.