Electric Gate Repair in Irving — On-Site in 60 Minutes, Fixed the Same Day

Fast, Reliable Electric Gate Repair Across Irving

Electric gate repair in Irving usually comes down to one of two diagnoses: a failed operator or a gate that was never properly powered and posted to begin with. We work both sides of that divide every week. Irving’s split between the master-planned Las Colinas corridor and the older south-side neighborhoods means the same complaint, a gate that won’t open, has two very different root causes depending on which zip code you’re calling from. Bastion Gate Repair sends technicians who know which one they’re looking at before they even park the truck. Call (866) 321-6117 if your gate is down, stuck, or only working when it wants to.

Call (866) 321-6117

Why Bastion Gate Repair Is Irving’s Preferred Electric Gate Repair Company

We’ve built our name in the Dallas area on one thing: we diagnose electric gate faults at the component level instead of quoting you a full system swap because that’s easier for the shop. In Irving specifically, that approach matters more than most places. A builder-grade operator that is tripping its breaker in a Las Colinas HOA community is frequently an undersized control board and a missing surge protector, not a dead motor. A sagging gate in a 1960s-era south Irving lot is usually a hinge post that has heaved in the clay, not a bad hinge. Homeowners and property managers around 75014, 75015, 75016, and 75017 trust us because we fix the actual problem, and we tell you when a repair is the better spend versus a replacement.

Brent Calloway, who leads our operation, is strict about that. We quote the repair you need, not the upsell we would prefer. Irving customers tell us that is why they stick with us when a gate fails a second time or when the HOA board asks which contractor should handle the community entrance.

Automatic Gate Repair in Irving

Automatic gate repair in Irving spans everything from a keypad that stopped accepting codes at a 75038 townhome to a full slide-gate operator failure at a 75062 commercial lot. When a homeowner or property manager calls us about an automatic gate that will not move, we start with the control side, because most gates we see in Irving fail electrically first. That means testing the opener, the safety sensors, the loop detector if one exists, and the board before touching mechanical hardware. Typical automatic gate repair in Irving runs $185 to $450 for common component failures like a sensor, keypad, or control board. A full operator replacement, when truly needed, usually lands between $900 and $2,400 depending on the gate type and whether we are also correcting the original wiring.

Opener and control-board diagnosis

Heat is the quiet killer of gate electronics in North Texas. We open a lot of control boxes in Irving that have cooked themselves after two or three summers. Board-level repair on brands like LiftMaster and FAAC costs less than most people assume. When the board is beyond saving, our Electric Gate Repair technicians quote a drop-in replacement and explain the surge protection we recommend so it does not happen again in August.

Safety sensor and loop detector work

Irving’s spring hail season knocks photocells out of alignment every year. If your automatic gate keeps reversing or stops midway, a jolted sensor is the first suspect. We realign or replace sensors and check the loop detector timing at the same visit, because the two systems talk to each other and one bad signal confuses the other.

Electric Gate Motor in Irving

Electric gate motor repair in Irving is its own specialty, and it is the call we get most often from Las Colinas HOAs and south Irving homeowners who have automated an old manual gate. A gate motor that hums but won’t move, or that trips its breaker on hot afternoons, is usually a capacitor, a gear assembly, or an overheating thermal overload. Motor-specific repair in Irving typically runs $220 to $520. When the motor itself is burned out, replacement swings from $700 to $1,800 on most residential swing and slide gates, and more on commercial operators.

Slide-gate motor replacement

Las Colinas has a lot of slide gates on commercial and HOA entrances. Those motors see constant cycles, and the builder-grade Linear and Viking units we replace were often sized too small for the duty cycle. We swap in a correctly rated motor and check the chain tension and limit switches on the same job. Half the “bad motors” we quote in Irving turn out to be limit switches and tension problems we can correct for a fraction of a replacement.

Swing-gate operator retrofits

South Irving is swing-gate country. When someone wants automation retrofitted to a gate that has stood manual for forty years, the first thing we check is the post, not the opener. An operator bolted to a heaving hinge post will destroy itself within a couple of seasons. We reset the footing, true the post, and then install an opener that matches the gate’s weight and swing arc. The order of operations matters.

Trusted Brands We Service in Irving

We work on nine major gate brands across Irving, including LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That breadth matters in a city where one street might have a Mighty Mule on a backyard cattle gate, two blocks later a FAAC on an HOA entrance, and a Viking on a commercial dock. We stock common replacement boards, sensors, and remote receivers for most of those brands locally, so Irving customers are not waiting on a parts truck from out of state. When we do order a part, we tell you the real timeline up front.

Common Electric Gate Repair Problems We See in Irving Homes

• Builder-grade operators failing early in Las Colinas: The planned communities in 75038 and 75039 were built fast, and many original gate operators were sized for the bid, not the duty cycle. We regularly replace Linear and LiftMaster units that never should have been installed on a daily-use community gate. The fix is a properly rated operator plus dedicated conduit and surge protection, which the original build usually skipped.
• Clay movement racking posts in south Irving: The 75060, 75061, and 75062 neighborhoods sit on expansive clay that shifts with every wet-dry cycle. Gate posts set shallow in the 1960s heave and tilt, and the gate starts scraping or refusing to latch. We reset the footing before any automation work, because a misaligned gate will eat a new opener in months.
• Storm damage to frames and safety systems: Irving’s spring hail and straight-line winds bend ornamental iron and knock photocells out of alignment. A gate that reverses for no reason after a storm usually has a sensor that got knocked askew or a frame that warped just enough to change the travel path. We true the frame and recalibrate the safety edge and sensors together.
• No power at the gate on older lots: A lot of south Irving garages and side gates were never wired for automation because the homes predate common opener use. When the owner wants a remote-controlled gate, we have to run a power line or design a solar opener system sized for the shade and exposure that specific gate actually gets. Slapping a solar panel on a shaded north-facing wall is a design failure we correct all the time.

Pricing for Electric Gate Repair in Irving, TX

We Also Serve Cities Near Irving

Bastion Gate Repair covers Irving and the surrounding metro, including Farmers Branch, University Park, Cockrell Hill, and Dallas. If your gate is at a property on the Irving line or a few miles out, call us and we will let you know which crew is closest to you that day.

FAQs About Electric Gate Repair in Irving