Farm & ranch
Wrought iron
Wood & steel frame
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Electric Gate Repair Across Farmers Branch
Electric gate repair in Farmers Branch typically runs $185 to $540 depending on whether we are replacing a control board, re-setting a hinge post, or re-aiming safety sensors. Most repairs in the 75234 zip code are completed in a single visit because we stock parts locally and send a technician who has worked on North Texas clay-soil gate failures for years. If your gate is stuck, sagging, or refusing to respond to the remote, call (866) 321-6117 and we will walk through what you are seeing before we even dispatch.
Farmers Branch is different from newer suburbs. These are mature lots, mostly developed between the 1950s and 1980s, where the gate that worked fine for fifteen years now rubs against the ground or strains against its own hinges. We know the streets, the soil, and the storm patterns here. That local context means we diagnose the actual failure instead of selling you a part you don’t need.
Why Bastion Gate Repair Is Farmers Branch’s Preferred Electric Gate Repair Company
Our Electric Gate Repair team has worked on more operators in this corner of Dallas County than most shops see across the whole metro. The call pattern here is consistent: a gate that worked for a decade starts binding after a wet spring, then fails completely after the first big wind event of summer. Farmers Branch homeowners call us because we already know what we are going to find before we pull into the driveway.
Brent Calloway built Bastion Gate Repair around a simple idea: diagnose the system, not just the symptom. That philosophy matters in Farmers Branch, where the real problem is often two feet underground, not in the operator box. We have pulled hinge posts out of black clay that had moved a full inch since the day they were set. That is not a motor problem. That is a footing problem. And we fix it correctly the first time.
Our reputation in 75234 has grown through word of mouth from homeowners near Valley View Lane, Josey Lane, and the neighborhoods east of I-35E. Property managers for small commercial sites along Dennis Lane have also come to rely on us for operator repairs that keep tenants and deliveries moving. We do not rush, we do not upcharge, and we do not recommend replacement when a repair is the honest answer.
Styles & brands we work with
Gate Access Control in Farmers Branch
Gate Access Control in Farmers Branch means the full chain of equipment that decides who gets in and who doesn’t, from the keypad at the curb to the control board inside the operator housing to the loop detector buried under the driveway. In built-out 75234 neighborhoods, many of these systems were installed years ago and are now failing quietly, one component at a time.
Keypad and Telephone Entry Systems
Older keypads on Farmers Branch gates take a beating from full sun and spring hail. The membrane buttons crack, the housing fades, and eventually the keypad stops registering codes entirely. We replace keypads and telephone entry units across 75234, matching the new unit to the existing operator so the whole system keeps talking. No rip-and-replace of a perfectly good motor just because the entry panel died.
Loop Detectors and Vehicle Sensors
If your gate opens fine with the remote but won’t open when a car pulls up, the loop detector under the driveway is usually the culprit. North Texas clay shifts, the loop wire eventually breaks, and the detector quits seeing vehicles. We install and tune new loop detectors in Farmers Branch driveways regularly, then test the gate’s auto-close timing so it never closes on a car again.
A keypad repair or loop detector replacement in Farmers Branch typically runs $165 to $380, including parts and labor. Exact numbers depend on what brand you have and how deep we need to dig to reach the old loop.
Commercial Gate Operator in Farmers Branch
Commercial Gate Operator work in Farmers Branch involves slide and swing operators on apartment complex entrances, office parking areas, and small industrial lots, many of them along corridors like Valley View Lane or east of Luna Road. These systems cycle dozens of times a day, and they fail differently than residential gates. When a commercial operator in 75234 goes down, tenants notice immediately.
Slide Gate Operators and Rack Repair
Most commercial slide gates in Farmers Branch use rack and pinion drive. The operator’s gear wears against the rack over thousands of cycles, especially in summer heat when everything expands and the gap between gear and rack tightens. We replace worn racks, repair motor brushes and capacitors, and reset travel limits so the gate stops exactly where it should, every time.
Fail-Secure and Fail-Safe Coordination
Commercial gates in Farmers Branch often need to coordinate with fire access requirements, meaning the operator must release or default in a specific way during a power cut. We verify that your gate’s fail-secure or fail-safe behavior matches what your property needs, and we match keypads, card readers, and remote controls to the operator’s logic board instead of slapping on whatever part is easiest. Commercial operator replacement or major repair in 75234 runs roughly $650 to $1,850 depending on the operator size and access control integration.
Trusted Brands We Service in Farmers Branch
We work on the brands Farmers Branch homeowners and property managers actually have installed. That includes Viking and Ghost Controls on residential swing gates, plus DoorKing and Elite on commercial slide operators across the area. Because we service these systems regularly, we keep common repair parts close by, which shortens turnaround for customers around Valley View and east toward Webb Chapel Road. When your operator is a brand most generalist handymen won’t touch, that is exactly the kind of system we see every week.
Common Electric Gate Repair Problems We See in Farmers Branch Homes
- Hinge posts kicked out of expansive clay. North Texas black clay swells in spring and shrinks in summer, and over decades that cycle can push a post out of plumb enough to rack a swing gate. We re-set the post in fresh concrete and then re-tune the operator, instead of forcing a motor to muscle a gate that no longer hangs straight.
- Wind-loaded solid-infill gates straining operators. Farmers Branch gets straight-line wind and spring hail that hits solid wood and metal gates like a sail. That load hammers the hinge bearings, the operator arm, and the control board’s current-sensing circuits until something finally gives.
- Storm power cuts leaving gates stuck closed. Every spring we get calls after a storm knocks out power and an electric gate will not move. Homeowners who don’t know their manual-release procedure end up climbing over or calling us in a panic. Know where your release is before you need it.
- Safety photocells misaligned after wind or ground shift. When a gate post moves even half an inch, the safety photo eyes that were aligned for years suddenly cross their beams and the gate refuses to close. This looks like a motor failure to most people. It is often a five-minute realignment, and we will tell you that instead of selling you a motor.
See the difference
Before
After
Before
After
Before
AfterPricing for Electric Gate Repair in Farmers Branch, TX
What you pay depends on what actually failed. Here’s what we see in 75234 right now: safety sensor realignment or replacement runs $120 to $240. A hinge post re-set in concrete, including re-plumbing and operator re-tuning, typically runs $350 to $700. A control board replacement on a residential operator runs $220 to $480 parts and labor. Commercial operator repairs start around $650 and climb from there based on the system’s size and how much access control is tied into it.
Every quote is given to you before any work starts. You agree to the number before we turn a wrench. Call (866) 321-6117 and describe what your gate is doing, and we will give you an honest range over the phone, then confirm it with a written estimate on site.
We Also Serve Cities Near Farmers Branch
Beyond 75234, our Electric Gate Repair in Farmers Branch service area reaches into the surrounding North Dallas suburbs. We regularly handle gate repairs in Addison, Carrollton, Irving, and University Park, carrying the same brand-specific parts and the same clay-soil expertise across the county line. If your gate is failing in a neighboring city, the same number applies: (866) 321-6117.
Serving Farmers Branch, TX — Our Local Coverage Area
We’re based in the Farmers Branch area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Electric Gate Repair in Farmers Branch
Nearly every automatic gate has a manual release, usually a pull handle or keyed lever on the operator itself. On slide gates with a vertical release, you pull the handle up and then push the gate by hand along its track. On swing gates, you disengage the operator arm from the gate leaf and move the gate manually. If you can’t find the release or the gate won’t budge, do not force it; call (866) 321-6117 and we will talk you through locating it, or dispatch to your address in Farmers Branch.
Because the post itself is moving, not the hinge bolts. Farms Branch sits on expansive black clay that swells when wet and shrinks when dry, and over a wet spring the ground around a decades-old post can heave enough to kick the post out of plumb by an inch. Tightening hinges only grinds the gate down further. We re-set the post footing in concrete, re-plumb the post, and then correct the operator limits. Call (866) 321-6117 if your gate is visibly sagging, because it will only get worse.
Yes. UL 325 compliance requires automatic gate operators to include entrapment protection, typically photo eyes or contact edges, that stops and reverses the gate when someone or something is in the path. Many older operators around 75234 were installed before current standards and lack adequate protection. We can add or replace safety edges and photocells to bring your gate up to code without replacing a functioning operator.
Not necessarily. Hail damage to a solid gate panel changes the gate’s weight distribution and wind profile, and dents along the leading edge can throw off the gate’s travel geometry, which makes a healthy operator work harder. Sometimes the fix is panel repair or hinge adjustment, not a motor replacement. We will test the operator’s current draw before recommending anything. Call (866) 321-6117 and we will assess it in Farmers Branch.
Yes, we repair and replace both on commercial systems in Farmers Branch. Older keypads are often from brands that no longer exist, and we can swap them for a compatible modern unit wired into your existing operator. Loop detectors can also be repaired or replaced, including digging out and reinstalling a failed loop in the driveway surface. Most commercial entry and loop repairs run $180 to $420 before any operator work is needed.
When the Ground Moves, the Gate Follows
Here is what we have learned working gates in Farmers Branch specifically: the gate almost never fails first. In built-out 75234 lots, the black clay under the hinge post moves during wet-dry cycles, the decades-old footing shifts, and suddenly a swing gate that closed perfectly for years is dragging against the concrete or binding at the latch end. The panel is fine, the motor is fine, and the problem is two feet beneath your fence line. That is why we assess soil and post footing before we ever quote an operator part here. Replacing a motor on a gate that is racked out of plane is wasted money, and we will never sell you that.
One call from a mature lot off Valley View sticks with us. A homeowner’s LiftMaster repair in Farmers Branch started with a swing gate that had been grinding for weeks until the arm finally jammed after a wet spring. The control panel checked out square, but the hinge post had kicked out of the clay. We pulled and re-set the post footing in concrete, re-plumbed the hinge post, corrected the sag, then reset the operator’s limits and re-aimed the safety photocells. The gate has cycled cleanly since, without replacing a gate that was never the problem. That is the difference between a gate technician who reads the gate and one who reads the soil underneath it.
If your electric gate in Farmers Branch is sagging, straining, or dead after a storm, call (866) 321-6117. We will ask a few questions, tell you honestly what we think is wrong, and schedule a visit at a time that works. Written estimate always comes before work begins.
Written by Brent Calloway, Owner at Bastion Gate Repair, serving Farmers Branch and the greater Dallas County area.