Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Mesquite
If your driveway gate is sagging, stuck, or refusing to open in Mesquite, we can usually have a tech at your door within hours, not days. Most gate failures in this part of Dallas County come down to three things: expansive clay soil heaving the posts, control boards that died quietly, and rust working through hinge welds for 40 years. We work on every brand you’re likely to have, from a 1980s chain-drive opener to a modern Ghost Controls system. Call (866) 321-6117 and we’ll diagnose it over the phone first, then give you a firm price before we roll a truck.
Bastion Gate Repair isn’t a general handyman service. Gates are all we do.
Why Bastion Gate Repair Is Mesquite’s Preferred Gate Repair Company
Mesquite homeowners keep calling us back because we understand what 50 years of Blackland Prairie clay does to a gate. Most shops will adjust the hinges and call it done. We look at the post, the footing, and the operator as one system, because in Mesquite they fail as one system. Brent Calloway built our service around that principle: diagnose the actual failure, not the symptom.
Our Gate Repair team carries parts for residential and commercial openers, and we don’t pad invoices with “diagnostic fees” that disappear into the total. The price you approve is the price on the invoice. For property managers running gates across multiple Mesquite entrances, that predictability matters. We also know the permitting process in Mesquite when a post reset requires a deeper pier than the original 24-inch footing, which is common in the 75150 area.
Written by Brent Calloway, Owner at Bastion Gate Repair, serving Mesquite and the surrounding Dallas County communities.
Styles & brands we work with
Commercial Gate Repair in Mesquite
Commercial Gate Repair in Mesquite means slide gates, cantilever gates, and barrier arms that run on operators most residential shops won’t touch: DoorKing, FAAC, BFT, Elite. We see a lot of these along the industrial corridors near Town East Boulevard and the distribution centers off 75150 and 75181, where a down gate stalls trucks and costs real money every hour. Typical commercial slide gate repair in Mesquite runs $450 – $1,800 depending on whether we’re replacing a loop detector, rebuilding a roller carriage, or swapping a failed operator.
Access Control and Loop Detectors
Most commercial gate failures in Mesquite aren’t mechanical. They’re electrical. A loop detector that stopped sensing vehicles, a keypad with corroded terminals, or a phone entry system that lost its programming. We diagnose the control side first because that’s usually where the problem lives. If your operator is a Viking or DoorKing and the board is dead, we can often retrofit a modern board that fits the existing enclosure rather than tearing out the whole unit.
Slide Gate Track and Roller Work
Mesquite’s clay soil does not move gently. Slab heave can knock a slide gate track out of level by half an inch, and that’s enough to make the gate bind, trip the entrapment sensor, and reverse. We reset track sections and replace worn roller trucks regularly on commercial properties along Military Parkway and the surrounding industrial streets. A gate that scrapes and shudders is wearing out its operator faster than it should.
Iron Gate Repair in Mesquite
Iron Gate Repair in Mesquite almost always starts with the hinge welds. On homes built from the 1950s through the 1980s, the original ornamental iron gates were welded, not bolted, and 40 years of North Texas heat and humidity have done the work you’d expect. A typical iron gate repair in Mesquite runs $200 – $600 for hinge replacements, rust grinding, and re-welding; if the post itself has rusted through at the base, you’re looking at $700 – $1,200 for a post replacement with a proper concrete pour.
Hinge Post Rust and Weld Failure
The hinge side fails first. Water pools at the base of the post, creeps into the weld joint, and the metal thins from the inside. By the time the gate sags visibly, the post is often structurally compromised. We cut out the rusted section, weld in new steel or a full replacement hinge post, and treat the joint so it doesn’t become next year’s project.
Realigning and Rehanging Vintage Gates
Some of the iron gates in Mesquite’s older neighborhoods are worth saving. They’re heavier and better-built than most of what’s sold today. When the gate is still straight and solid but the posts have moved, we un-hang it, rebuild the post footings in fresh concrete with deeper piers, and re-hang the gate so it swings level and latches cleanly.
Trusted Brands We Service in Mesquite
We’re certified familiar with nine major gate brands, and we stock local parts in our service vehicles for the ones Mesquite homeowners actually have: LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule. That matters when your operator died on a Friday and you don’t want to leave the driveway open all weekend. We carry common control boards, safety sensors, and remote transmitters so one trip usually finishes the job.
See the difference
Before
After
Before
After
Before
AfterCommon Gate Repair Problems We See in Mesquite Homes
- Hinge post heaving from expansive clay. The Blackland Prairie clay under Mesquite swells when wet and contracts in drought, tilting gate posts a few degrees and making the gate bind at the latch. Hinge adjustments alone don’t fix it because the footing is the problem, not the hardware.
- Obsolete control boards in legacy operators. Older LiftMaster and Linear units from the 1990s and 2000s are now unsupported, and when the board fails, replacement is the only honest fix. We can often reuse the existing arm and track, which saves you $300 – $500 versus a full new operator.
- Rusted hinge welds on steel gates. Decades of rain, sprinkler overspray, and humidity concentrate rust at the weld joints. The gate looks fine until the weld lets go and the gate drops. This is a structural failure, not a cosmetic one.
- Safety sensor faults on pre-2016 operators. Gates installed before modern UL 325 entrapment standards often lack photocells or have dead ones. If your gate closes on a car or person without reversing, that’s not a minor inconvenience. It’s a safety defect that needs addressing immediately.
Pricing for Gate Repair in Mesquite, TX
Here are the numbers we quote most often in Mesquite, for real: hinge and realignment work runs $200 – $600. Post resetting and concrete footing rebuilds run $400 – $900 per post. Control board replacement runs $350 – $800 depending on the operator. A full operator replacement with installation lands between $1,200 – $2,800 for a residential swing or slide gate. Commercial slide gate repairs start around $450 and go up based on the operator and access control hardware. We quote everything up front and you approve the number before any wrench turns.
We Also Serve Cities Near Mesquite
Beyond Mesquite, our technicians cover the neighboring communities of Balch Springs, Sunnyvale, Seagoville, and Hutchins. The same clay soil and the same aging housing stock follow you east and south, and the same repair approach applies. If you’re right on the line between Mesquite and one of those cities, call and we’ll work out the fastest route to you.
Serving Mesquite, TX — Our Local Coverage Area
We’re based in the Mesquite area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Mesquite
If your gate post is set in the original concrete from a 1960s – 1980s build, you almost certainly need the post reset, not just hinge adjustment. Mesquite’s expansive clay shrinks during dry summers and the whole footing tilts. Adjusting hinges on a heaved post buys you a few months before the gate binds again. Call (866) 321-6117 and we’ll check the post plumb and the footing depth before recommending a fix.
If your operator is less than 15 years old and the motor and gearbox are sound, we can usually add modern UL 325-compliant photocells and an edge sensor. If the control board is obsolete, no retrofit exists. The board is the brain, and if the manufacturer no longer produces it, the unit is a safety liability. We’ll tell you which camp yours falls into after a 20-minute inspection.
Yes. A rusted hinge weld is a structural failure waiting to happen, not a cosmetic issue. The gate may hold its own weight today, but the next strong wind or an errant bump from a car can snap it at the joint and drop a 200-pound gate onto a person or vehicle. If you can see flaking rust and metal loss at the weld, schedule a repair before it fails catastrophically.
Original concrete footings from Mesquite homes built before the 1990s generally last 25 – 40 years before the wet-dry cycles of Blackland Prairie clay crack or heave them. Footings poured shallow, 18 – 24 inches, fail sooner than deeper piers. When we reset a post, we pour at least 36 inches with rebar, sometimes more depending on the gate weight and soil condition on your specific lot.
Yes, that’s a core part of our daily work. We service slide gates with loop detectors, keypads, card readers, and phone entry systems on commercial properties across Mesquite. Most of the time the gate is fine and the sensor or access control component is the failure, so we start there rather than quoting a whole new gate. Call (866) 321-6117 and describe what the gate is doing, or not doing, and we’ll tell you what we think before we come out.
Written by Brent Calloway, Owner at Bastion Gate Repair, serving Mesquite and the surrounding Dallas County area.