Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Electric Gate Repair Across Garland
An electric gate that won’t open or close is more than an annoyance in Garland. It’s a security gap on your property and a daily logjam for your driveway. Bastion Gate Repair fixes electric gate systems across Garland, from worn operator motors and dead keypads to misaligned safety sensors and fried control boards. We work in the tight side yards and shared driveways that define so many Garland lots, and we’ll get your gate cycling again without making everyone park on the street. Call (866) 321-6117 for service in Garland, or keep reading to see what’s actually involved.
Why Bastion Gate Repair Is Garland’s Preferred Electric Gate Repair Company
Garland homeowners call us because we diagnose the whole gate system, not just the part that finally stopped working. Led by Brent Calloway, our technicians work on virtually every major gate brand, including LiftMaster, FAAC, BFT, and Mighty Mule. When a Garland gate fails, the root cause is often two or three linked problems: a photo-eye out of alignment, a hinge post slowly leaning, a control board that’s taken one too many North Texas heat cycles. We find all of it.
Our Electric Gate Repair team is brand-agnostic. That means we don’t show up trying to sell you a new operator when a $120 sensor swap would fix the problem. For the older homes in Garland’s 75040 – 75043 ZIPs, that matters. Those gates sit on original posts, often cedar, and the clay soil has been working against them for fifty years. We understand that dynamic because we’ve corrected it hundreds of times.
Styles & brands we work with
Electric Gate Motor in Garland
Electric Gate Motor service in Garland means dealing with both the operator itself and the pad it’s bolted to. Garland’s expansive clay soil swells and shrinks through every wet-dry cycle. That movement tilts hinge posts and operator pads out of plumb, which makes even a healthy motor work against binding rails and misaligned racks. The fix usually isn’t just the motor. It’s the motor plus re-leveling and re-anchoring the pad so the motor isn’t fighting the gate every cycle.
A typical electric gate motor replacement in Garland runs $450 to $900 for a residential swing or slide operator, including labor. Motor repair, like replacing a burned capacitor or stripped drive gear, typically runs $180 to $350 depending on the brand and how much disassembly the model requires. We quote a firm price before any work starts. No surprises when you see the invoice.
Operator Diagnosis and In-Place Repair
Most Garland repairs happen with the gate still in place. We check the operator’s drive train, limit switches, and force settings, then verify the photo-eyes and safety loop are talking to the board correctly. If the operator can be repaired rather than replaced, we’ll tell you plainly. That’s the call we’d want someone to make for us.
Motor Replacement on Tight Garland Lots
Some Garland side yards leave only inches between the gate and the house. We bring low-clearance tools and work deliberately, keeping the gate operational for as long as possible so the cars parked behind it can get out. Most motor swaps on a tight Garland lot take one visit, even when the original post needs re-setting at the same time.
Gate Access Control in Garland
Gate Access Control in Garland covers the entry side of the system: keypads, remotes, intercoms, loop detectors, and phone-based access for shared driveways. Many Garland homes, especially in the older neighborhoods off Garland Road and near downtown, have shared driveways with a gate that two or three households depend on. When the keypad dies or a remote stops syncing, it’s not one person locked out. It’s three households and their cars.
Access control repair in Garland typically runs $120 to $280 for keypad replacement or reprogramming, and $90 to $200 for remote control replacement and pairing. Full keypad-and-receiver upgrades, including weather-sealed hardware built for Texas sun, run $300 to $600. We quote the job before touching a single wire.
Keypad and Remote Programming
We replace, reprogram, and sync keypads and remotes for LiftMaster, Linear, DoorKing, and other major systems. If a homeowner has lost a remote or a tenant moved out, we can clear the codes and issue fresh ones the same afternoon. It’s a small job that keeps the gate useful for everyone.
Loop Detectors and Safety Edges
Garland shared driveways often rely on vehicle loop detectors so the gate opens automatically when a car pulls up. Clay soil movement can crack a loop wire underground, which makes the gate ignore an approaching car. We locate the break, repair or replace the loop, and get the automatic cycle working again. For gates with reversing safety edges, we check the edge sensor every motor repair, because a failed edge turns a sliding gate into a hazard.
Trusted Brands We Service in Garland
We stock common repair parts for LiftMaster, FAAC, BFT, and Mighty Mule systems, which means many Garland repairs don’t wait on a parts shipment. Our technicians know the failure patterns on each brand: which LiftMaster boards run hot in Texas summers, which FAAC limit switches drift, which Mighty Mule remotes lose pairing after a power surge. That familiarity means fewer return trips and a repair that works the first time. If your gate is a less common brand, we’ll source the part and tell you the real timeline before we start.
See the difference
Before
After
Before
After
Before
AfterCommon Electric Gate Repair Problems We See in Garland Homes
- Gate dragging or binding on a slide track. Clay soil pushes the hinge post out of plumb, so the gate rides hard on the rack and pinion. The operator keeps tripping its force limit, and eventually the gear strips.
- Original cedar hinge post rotted at the groundline. In the 75040 – 75043 ZIPs and older areas near downtown, a sagging gate is frequently a rotted post. Dead operator symptoms are often the same call: the motor gets blamed, but the post is the real failure.
- Photo-eye misalignment on a tight side yard. There’s no room to nudge the gate panel by hand, so when the photo-eye drifts, the gate refuses to reverse or close at all. A misaligned sensor can make a healthy gate act broken.
- Control board failure from heat and humidity. Garland summers bake operator boards inside their enclosures. Capacitors swell, relays stick, and the board forgets its limits. We replace boards and also check ventilation so the new one lasts longer.
Pricing for Electric Gate Repair in Garland, TX
Most electric gate repairs in Garland fall between $150 and $600, depending on what failed and what brand you have. Sensor misalignment or a remote reprogramming sits at the low end. A control board replacement or a motor swap on a lift-heavy slide gate runs higher. If the original cedar post has rotted and needs a new footing, add $250 to $500 for post replacement and concrete work. That’s the Garland reality: the oldest lots hide expenses a generic gate company never factors in. We give every Garland customer a fixed price before work starts. Call (866) 321-6117 and we’ll come out, diagnose the system, and quote it honestly.
| Service | Typical Range in Garland |
|---|---|
| Remote control replacement & pairing | $90 – $200 |
| Keypad replacement or reprogramming | $120 – $280 |
| Photo-eye realignment or replacement | $110 – $250 |
| Control board repair/replacement | $200 – $480 |
| Gate motor repair (drive gear, capacitor) | $180 – $350 |
| Gate motor replacement | $450 – $900 |
| Cedar post replacement with new footing | $250 – $500 |
We Also Serve Cities Near Garland
We work throughout the Dallas suburbs, including Richardson, Sunnyvale, University Park, and Mesquite. These are our regular routes from our DeSoto base, and we know the gate hardware common to each area. Wherever the job is, the same rule applies: diagnose the system, quote the price, fix it correctly. For service beyond Garland, our Electric Gate Repair in Garland team covers the whole corridor with the same specialist approach.
Serving Garland, TX — Our Local Coverage Area
We’re based in the Garland area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Electric Gate Repair in Garland
Yes. We repair most operators in place on tight Garland driveways. There’s usually just enough working room beside the gate for motor and sensor service without removing the panel. We keep the gate cycling for the cars parked behind it whenever possible, and if we must stop the gate briefly, we will tell you when and for how long. Call (866) 321-6117 to schedule it.
Usually the post has moved, not the hinges. Garland’s clay soil swells and shrinks with the wet-dry cycle, pushing the hinge post or operator pad out of plumb. Adjusting the hinges won’t help if the post itself has shifted or rotted at ground level. The real fix is re-plumbing or replacing the post, then re-aligning the gate and the operator to match. It is the most common underlying problem we find in older Garland lots.
Only if the safety sensors and reversing function are working. We test the photo-eyes, the force settings, and the reversing edge before anything else. A LiftMaster or DoorKing that is ten or fifteen years old may still run fine, but a failed photo-eye makes it dangerous. We’ll tell you whether the board and sensors can be repaired or whether it’s time to replace the operator. You’ll know the cost either way before any work starts.
Often yes, if the lot has room for a slide track to run along the fence line. Many narrow Garland driveways do better with a slide gate, which does not swing into the driveway or the house. The conversion involves setting a new track and operator, and replacing the post if the original is unsound. We handled a LiftMaster slide gate on a shared driveway in the 75042 area near downtown Garland where the gate was dragging hard on its rack. After re-setting the rotted cedar post, re-plumbing the track, and re-aiming the photo-eye, the gate cycled cleanly the same afternoon with the driveway open the whole time.
Yes, we specialize in it. Shared driveways in Garland often mean multiple households, several remotes, and a keypad that takes daily use. We replace and program keypads, clear old codes, and install weather-sealed access hardware meant for Texas summers. A shared driveway gate that only opens for one household is a problem we fix quickly, usually in one visit. Call (866) 321-6117 for an exact quote, and we’ll come out to diagnose it.
Written by Brent Calloway, Owner at Bastion Gate Repair, serving Garland and the surrounding Dallas suburbs.