Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateFast, Reliable Gate Repair Across Irving
Gate repair in Irving splits into two very different jobs depending on which side of the city you call home. In the older south Irving neighborhoods around 75060 and 75062, a gate that won’t close usually means a post that has heaved in the expansive clay. A few miles north in Las Colinas and the 75038 and 75039 corridor, the same complaint typically traces to a failed operator board or access-control component behind an ornamental gate. Our Gate Repair team handles both, and we are already familiar with the failure patterns on each side of Irving before we even pull up. Call (866) 321-6117 and tell us the ZIP code and what the gate is doing. We will know what to bring.
Irving covers 75014, 75015, 75016, and 75017 on our dispatch map, and we run calls across all of them, from the mid-century lots south of Highway 183 to the gated communities and office parks around Lake Carolyn. Wind, hail, clay movement, and a lot of direct sun shape what fails here. A gate repair company in Irving has to understand all of it, not just how to swap a hinge.
Why Bastion Gate Repair Is Irving’s Preferred Gate Repair Company
Homeowners and property managers in Irving call us because we speak both languages this city uses. On one side, you have decades-old residential gates on south-side streets with posts set long before modern footing standards. On the other, you have HOA-governed ornamental iron and automatic operators on master-planned Las Colinas properties where the architecture review board watches every repair. Our Gate Repair in Irving coverage is built on knowing which set of rules applies where.
Brent Calloway built our team around brand-agnostic diagnosis. We don’t default to replacing a gate because it’s easier to quote. We open the panel, test the logic board, check the limit settings, and find the actual fault. That saves Irving customers money, especially in neighborhoods where a full replacement would drag through an HOA approval process.
Our reviews from Irving mention the same things: we show up with the right parts, we don’t pad the ticket, and we tell homeowners when a repair is smarter than a replacement. That trust matters in a market where gate failures are often urgent. You don’t want to interview three contractors while a sagging gate keeps the driveway open all night.
Styles & brands we work with
Sliding Gate Repair in Irving
Sliding gate repair in Irving is in steady demand, mostly in the 75038 and 75039 corridors where gated office parks, apartment entries, and larger planned-community lots favor slide gates over swing models. On a slide gate, the usual suspects are a worn drive chain, a ground-track that has shifted with clay movement, a failed limit switch, or a loop detector that no longer reads vehicles. We also replace bent rollers and realign the guide wheels so the gate doesn’t bind mid-travel. Most sliding gate repairs here run $225 to $650, depending on the drive component and how much has to be removed and re-aligned.
Track, Roller, and Chain Work in Irving
North Texas clay doesn’t just affect posts. It shifts the concrete pad or rail a slide gate rolls on. A gate that was smooth three years ago can suddenly drag or chatter because the ground under the track has moved a fraction of an inch. We shim, re-level, or replace the track section, then tune the chain and limits so the operator isn’t fighting the load.
Operator and Limit-Switch Repairs
When a slide gate opens halfway and stops, or reverses on its own, it’s often a limit switch or a control board input failure, not the motor. We test the operator under load before proposing parts. On Irving commercial properties with Viking or FAAC slide operators, this means a faster diagnosis and no needless replacement work.
Wrought Iron Gate Repair in Irving
Wrought iron gate repair in Irving is common on both sides of the city, but for different reasons. South of 183, older ornamental gates suffer rust at the bottom rails and hinge welds after decades of rain splash and sprinkler contact. In Las Colinas, the ironwork is newer but often takes wind-driven impact and hail damage that dents stiles and loosens pickets. Wrought iron is forgiving to weld, and most repairs don’t require removing the gate from its posts. Typical repairs run $180 to $480, with full re-hangs or frame straightening at the higher end.
Rust Repair and Pickup Replacement
We cut out rusted sections at the bottom rail and weld in new matching stock. We also replace missing pickups, re-secure loose pickets, and treat the repaired area so it doesn’t rust through again in six months. On south Irving gates that have been painted multiple times, we’ll grind to clean metal before welding, which is the only way to get a solid bond.
Straightening Storm-Bent Frames
Straight-line wind can bow a solid-infill wrought iron gate enough that it misses the latch by an inch. We have pulled bent stiles back into plane, re-welded cracked scroll joints, and re-hung the gate so it swings free, all without replacing panels that still have years of life. That’s the money-saving part most homeowners don’t expect from a repair call.
Trusted Brands We Service in Irving
We carry parts and know the logic boards for the brands Irving properties already have installed. Mighty Mule openers are everywhere on south Irving residential gate posts, and we keep common Mighty Mule control boards and arm kits stocked for same-week repairs. LiftMaster dominates the newer Las Colinas driveway and community gates, and we service the full line, including myQ-enabled operators. FAAC and BFT hydraulic operators show up on plenty of Irving commercial and multifamily slide gates, and our techs work on their boards, limit systems, and hydraulic pumps without calling for a factory rep. One call covers it, no matter what your gate says on the housing.
See the difference
Before
After
Before
After
Before
AfterCommon Gate Repair Problems We See in Irving Homes
- Heaved or tilted hinge posts on south-side lots. Expansive clay under 75060 and 75062 moves with every wet-dry cycle. The post tilts, the gate panel racks, and the latch stops lining up. The fix is a reset footing, not a new hinge.
- Wind-bent frames and failed operators in Las Colinas. North Texas straight-line winds and spring hail load solid-infill gates like sails. Frames bend, welds crack, and operator arms strip under the added resistance.
- Operator and control-board burnout from heat and UV. 75038 and 75039 have open, sun-exposed gate equipment. Boards cook. Loop detectors fail. Photocells lose alignment. Slide gates end up stuck open or cycling on their own.
- Rusted bottom rails and hinge welds on older ornamental gates. Decades of lawn sprinkler spray and rain splash take out the lower rail first. A gate that droops at the latch corner often has a rusted-through hinge weld, not a worn hinge pin.
In south Irving off the older 75060 streets, we answered a call where a decades-old swing gate had dragged for months. The homeowner assumed hinges. Our tech found the hinge post had heaved in the clay and racked the whole panel. We reset the post footing, did a proper sag correction, and re-hung the gate so it latched clean again. A few miles north in Las Colinas, the identical complaint usually ends at a LiftMaster operator or DoorKing access board instead. That split is the single most useful thing to know about gate repair in this city.
Pricing for Gate Repair in Irving, TX
Expect to pay $150 to $280 for a basic hinge and latch realignment on a standard Irving driveway gate. Post resets in clay-heavy south Irving soil run $275 to $550, depending on whether we need to pour a new footing or can stabilize the existing one. Operator and control-board repairs fall between $225 and $650. Full wrought iron frame straightening after wind or hail runs $180 to $480. Full slide gate track and roller work averages $300 to $600. The price is quoted and agreed before any work starts. You’ll know the number, the parts, and the labor before we touch the gate. Call (866) 321-6117 for a free estimate over the phone or on-site.
Key Takeaways
- South Irving gate sticking is usually a heaved post; Las Colinas gate sticking is usually a failed operator or board.
- Most sliding and wrought iron gate repairs in Irving run $180 to $650.
- Wind, hail, UV, and expansive clay are the four stressors that shape Irving gate failures.
- We stock parts for Mighty Mule, LiftMaster, FAAC, and BFT, covering the brands already on Irving properties.
- Price is quoted and agreed before any work begins. Free estimates by phone.
We Also Serve Cities Near Irving
Our Gate Repair team covers Irving daily and runs calls to the surrounding area. If you’re managing a gated property in Farmers Branch, University Park, Cockrell Hill, or Dallas, we handle the same brands and failure patterns, and often have a truck closer than you’d think. Call (866) 321-6117 and ask for a gate check on your specific entrance.
Serving Irving, TX — Our Local Coverage Area
We’re based in the Irving area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Repair in Irving
First, pull the disconnect handle or turn the manual-release key on the operator housing, which disengages the motor from the drive. On most LiftMaster and Mighty Mule operators in Irving, this is a red handle or a keyed cylinder on the side of the box. Once the motor is disengaged, push the gate slowly by hand. On slide gates, keep your hands clear of the track and rollers, and never let the gate roll free downhill. On swing gates, push at the latch stile, not the hinge side. If you have an FAAC or BFT hydraulic operator, the manual release is a valve or a pump bypass, not a lever, and it can be counterintuitive. Call (866) 321-6117 and we’ll walk you through your specific model while a truck heads your way.
Because the soil is different. South Irving sits on expansive clay that swells after rain and shrinks in drought, which heaves and tilts gate posts set decades ago. A sticking gate in 75060 is usually a racked panel on a moved post. In 75038 and 75039, the newer builds have deeper, engineered footings, so the gate structure stays true and the weakness shifts to the operator, board, sensors, and access-control components. Same symptom, two different failures, a few miles apart.
Yes. Under UL 325 and current Texas accessibility standards, any automatic gate operator in Irving must have a functioning entrapment protection system: primary and secondary safety devices such as photocells, contact edges, or an inherent sensing system. That applies to residential driveway gates just as much as HOA and commercial entrances. If your gate reverses on contact or cycles without stopping, the safety edge or photocell may be misaligned or dead. That is a safety issue, not a convenience fix, and it’s one we treat as urgent. Call (866) 321-6117 and we’ll test the full safety circuit before anything else.
Yes, and in Irving it happens every storm season. A solid-infill ornamental or wrought iron gate catches wind like a sail. Straight-line winds over 60 mph bow the frame, crack welds at the stile joints, and overload operator arms that were sized for normal weight, not wind loading. Hail dents uprights and loosens pickets. Bent frames often still look fine from the street, but they miss the latch, rub the post, or kill the operator with added resistance. Have it checked after a bad storm. The repair is typically cheaper before the damage spreads through the whole panel.
Yes. We work on LiftMaster, FAAC, BFT, Linear, Viking, Ghost Controls, DoorKing, Elite, and Mighty Mule, covering nearly every operator already running on Irving residential driveways and commercial entrances. We stock common control boards, limit switches, and safety-edge parts locally, which shortens most repairs compared to shops that special-order everything. Call (866) 321-6117, tell us the brand and what the gate is doing, and we’ll bring the parts we’re likely to need.
Written by Brent Calloway, Owner at Bastion Gate Repair, serving Irving and the greater Dallas metro. For gate repair, electric gate repair, or gate installation, call (866) 321-6117 for a free estimate.